Remote codes

Craig Soundbar Remote Codes & its Program Instructions in detail

If you are the one who is looking for craig soundbar remote codes for a long time, then you are at the right place to check out. The below discussion will be supportive to deliver the massive collection of codes of different digits. So, based on your requirement, you can go ahead and use the right codes. When it comes to process, there are certain steps that you need to follow and make use of it. Now, let’s get into the discussion and move ahead.

Craig Soundbar Universal Remote Codes

(3 Digit) Craig Soundbar Universal Remote Code 

  • 856

(4 Digit) Craig Soundbar Universal Remote Codes 

  • 1484
  • 6222
  • 0073
  • 0642
  • 1036
  • 4465
  • 4466

(5 Digit) Craig Soundbar Universal Remote Codes 

  • 10073
  • 06222
  • 11822
  • 16222
  • 10180
  • 00073

Steps to program Craig Soundbar with remote codes

  • When it comes to programming method to start, it is necessary for you to flip “Craig Soundbar ON”.
  • After the above process is done, you need to stay in Setup button.
  • Now, with the support of using quantity buttons, all you need to search for the codes which are mentioned in the above list.
  • So, if you are the one who properly entered the right or working code, then you can see that the LED on your remote will start to blink.
  • In case, if the code is wrong, obviously you can’t see that the light is blink. So, all you need to search for the right codes until it blinks.

These are the main steps that you need to follow without skipping it for sure.

Steps to line up Craig soundbar remote using Auto explore

If you have a look at auto search method, it can be done through scanning procedure through remote. Based on the working code, the scanning process will be done. To make this thing, all you need to follow the below steps.

  • Firstly, you need to turn ON the device that you would like to operate.
  • Now, make sure to have your remote ON and tap on the button that you would like to access for few seconds. Then, the LED will show that the gadget is ready to program.
  • Make sure to target the device and tap on “CH+” “CH-” switches. You can see that the remote will indicate ON/OFF signals. In order to flip off, you can go with up or down keys.
  • Now, you need to check out the code by using power key and now the device will ON. If it is started supporting, then it is programmed well.
  • You need to tap the device button when it comes to retailer the code. If the code is stored properly, the LED will start blink.

How to handle with Manual method

  • First of all, it is important for you to turn ON the device.
  • Now, make sure to tap the TV button on your remote.
  • After that, it is necessary for you to tap and hold the setup button until the light blinks.
  • Next, you need to enter the keycode where you can get it from programming instruction.
  • If the procedure is followed, you need to tap and hold the power button.

How to access Craig soundbar remote with code explote

If you are struggling to place the key code which will work for the device during that stage, then you can able to setup customary faraway when it comes to search mode according to right one. Let’s get into the steps below.

  • At first, you need to turn ON the device.
  • Now make sure to tap and hold the setup button.
  • You need to enter 3 digit codes.
  • Now, it is for you to hold the power button and tap the channel up until the device is turning OFF.

The above steps may take time to process. But make sure to focus on the right codes. If it is not working, you don’t need to be worried about it. Yes, you can move ahead with other codes which will work, but you need patience.

You may also like: How To Program poloroid tv remote code to control?

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button